Manually remove lighting presets and multi-way circuits

Nokia Dial

Unlink Dial Switch from Controlling Another Switch:

  • Press and hold the set button on the Dial switch for 3 seconds. It will beep and the LED indicator will begin blinking green.
  • While the LED is blinking green, press and hold the set button again for 3 seconds. It will beep and LED will start blinking red.
    Tip: if you plan on unlinking multiple devices, tap the set button once to put it into multi-unlink mode. It will beep and its LED will begin double-blinking red. This will allow you to unlink multiple devices without repeating these first steps for each device you unlink. When finished with the steps below, return to the Dial switch and tap the set button once to take it out of multi-unlink mode otherwise it will automatically drop out of this mode after 4 minutes of inactivity.
  • At the other device, press and hold the set button until you hear a double beep
    Note: if your responder is a Keypad, make sure you tap the button you wish to remove as a responder first before pressing and holding the set button.
  • The Dial LED will stop flashing to indicate the unlink is completed.

Nokia Paddle

Unlink Paddle from controlling another switch:

  • Press and hold the set button on the Paddle for 3 seconds. It will beep and the LED indicator will begin blinking green.
  • While the LED is blinking green, press and hold the set button again for 3 seconds. It will beep and LED will start blinking red.
    Tip: if you plan on unlinking multiple devices, tap the set button once to put it into multi-unlink mode. It will beep and its LED will begin double-blinking red. This will allow you to unlink multiple devices without repeating these first steps for each device you unlink. When finished with the steps below, return to the Paddle and tap the set button once to take it out of multi-unlink mode otherwise it will automatically drop out of this mode after 4 minutes of inactivity.
  • At the other device, press and hold the set button until you hear a double beep.
    Note: if your responder is a Keypad, make sure you tap the button you wish to remove as a responder first before pressing and holding the set button.
  • The Paddle LED will stop flashing to indicate the unlink is completed.

Nokia Keypad

Unlink a Keypad button that controls another switch or Keypad button:

  • At the Keypad, tap the button you want to program.
  • Press and hold the set button on the Keypad for 3 seconds (it will beep and the LED indicator on the selected button will begin blinking green).
  • While the LED is blinking green, press and hold the set button again for 3 seconds. It will beep and LED will start blinking red.
    Tip: if you plan on unlinking multiple devices, tap the set button once to put it into multi-unlink mode. It will beep and its LED will begin double-blinking red. This will allow you to unlink multiple devices without repeating these first steps for each device you unlink. When finished with the steps below, return to the Keypad and tap the set button once to take it out of multi-unlink mode otherwise it will automatically drop out of this mode after 4 minutes of inactivity.
  • On the other device, press and hold the set button until you hear a double beep.
    Note: if your responder is a Keypad, make sure you tap the button you wish to remove as a responder first before pressing and holding the set button.
  • The Keypad button LED will stop flashing to indicate the unlink is completed.

Nokia Outlet

If you no longer wish to have the Outlet control another device when tapping on its set button or via Load Sense, follow these steps

  • At the Outlet, press and hold the set button for the corresponding outlet for 3 seconds. It will beep and LED will start blinking green.
  • While the LED is blinking green, press and hold the set button again for 3 seconds. It will beep and LED will start blinking red.
    Tip: if you plan on unlinking multiple devices, tap the set button once to put it into multi-unlink mode. It will beep and its LED will begin double-blinking red. This will allow you to unlink multiple devices without repeating this first step for each device you unlink. When finished with the steps below, return to the outlet and tap the set button once to take it out of multi-unlink mode otherwise it will automatically drop out of this mode after 4 minutes of inactivity.
  • At the other device, press and hold the set until you hear a double beep.
    Note: if your responder is a keypad, make sure you tap the button you wish to remove as a responder first before pressing and holding the set button.
  • The controllers LED will stop blinking red to indicate the unlinking is completed.